Mesalabs ProChem BD测试包,Bowie-Dick Type Tset Pack,CI-BDTLF-20，CI-BDTLF121-20

产品：Bowie-Dick测试包

厂家：Mesalabs

产地：美国

用途：预真空蒸汽灭菌器的空气排出性能测试

包装：20个/盒，4盒/箱

效期：自生产日后3年

Mesalabs ProChem B-D测试包

Bowie-Dick Type Test Pack 简称B-D测试包，用于预真空压力蒸汽灭菌器的抽真空性能测试。 产品为一个多层纱布的包裹，包裹内部是一个测试卡片，模拟空气排除实验，根据其中测试卡片的颜色变化，判断实验是否成功。

                     使用前                                                       测试成功                                              测试失败

Mesalabs建议每天使用预真空蒸汽灭菌锅前，使用1个B-D测试包，空载时进行测试，将B-D测试包放置在灭菌器的底部支架上，靠近排气口的上方，测试时不用拆开测试包，灭菌后取出拆开测试包，查看最中心的指示卡，指示卡上的粉色完全变为黑色（132-134℃）或棕色（121℃），说明验证成功。

◆Air Removal Test Pack – Intended to evaluate the performance of the Air Removal (vacuum) system of Pre-Vacuum equipped Steam Sterilizers.

空气排出测试包-评估预真空蒸汽灭菌器的空气排除（真空）性能。

◆Pre-assembled, disposable test pack. After exposure, unwrap pack and remove the indicator sheet for your records.

预装配的一次性测试包。灭菌后，解开包裹，取出试纸记录结果。

◆510(k) notification and meets AAMI, EN-867-3 and ISO 11140 air removal test.

符合510（k），AAMI，EN-867-3和ISO11140空气排除测试标准。

◆Lead Free Ink on Indicator Sheet – Safer for medical personnel and the environment.

试纸采用无铅油墨-保证医疗人员和环境的安全。

◆Distinct, non-reversible pink to black color change – easy to interpret.

独特的不可逆的粉红色到黑色的变化-容易判读。

产品列表：

货号 产品描述 备注 包装规格

CI-BDTLF-20 Bowie-Dick测试包

121℃，10分钟

或132-134℃，3.5分钟

紫色小盒

20个/盒，4盒/箱

CI-BDTLF121-20 Bowie-Dick测试包，121℃专用

121℃，11分钟

绿色小盒

20个/盒，4盒/箱

CI-BD110

Bowie-Dick测试卡 134℃，3.5分钟 100个/盒

CI-BD110：灭菌后蓝色变为黑色，变色不可逆

Procedures for Use

Test sterilizer once a day.

Test at the beginning of each day. A shortened cycle should be used to preheat the system (i.e. omit the drying phase). If the sterilizer is in continual use, then testing can be performed at any time, but it should be tested at the same time every day.

Place the pack on the bottom rack in the front section of the sterilizer, near the door and over the drain.

The test is most accurate when nothing else is in the chamber, so do not use this cycle to sterilize items or packs. Other items in this cycle may invalidate the test.

Run a pre-vacuum cycle following the parameters printed on the indicator instructions. You may eliminate the drying phase to save time without affecting the test.

After the cycle is complete, remove the pack and open to examine the indicator sheet. CAUTION! Test pack may still be hot so use caution when handling to avoid injury.

Record the necessary information on the sheet (or in a log book) and store for your records.

The filter paper pack can be discarded into a paper recycle bin.